Key takeaways
- The PC will not boot or show a display after an overclock or memory profile change.
- You enter an unstable voltage or timing setting and cannot reach the BIOS.
- The board shows repeated restarts after a BIOS update, as support pages commonly suggest.
- You forgot a BIOS setup password, on boards where the password is stored in resettable memory. Some boards handle passwords differently, so read the manual.
- You are troubleshooting a no-POST problem and want a known-default starting point.
Clearing CMOS resets your motherboard’s BIOS settings to factory defaults, and you do it by powering off and unplugging the PC, then using the board’s Clear CMOS button, a jumper, or by removing the coin cell battery for a short time. It is the standard fix for a PC that will not boot after an overclock, memory change or bad setting, and it does not touch Windows or your files.
What CMOS actually is
The CMOS is the small memory area on a motherboard that stores BIOS or UEFI settings such as boot order, memory profile, fan curves and overclocks. A coin cell battery, usually a CR2032, keeps that memory and the clock alive when the PC is unplugged. Clearing CMOS removes those stored settings, so the board loads its defaults on the next start. Your operating system and personal data live on your drive and are unaffected, though a changed boot or storage mode can make Windows complain until settings are restored.
When to clear CMOS
- The PC will not boot or show a display after an overclock or memory profile change.
- You enter an unstable voltage or timing setting and cannot reach the BIOS.
- The board shows repeated restarts after a BIOS update, as support pages commonly suggest.
- You forgot a BIOS setup password, on boards where the password is stored in resettable memory. Some boards handle passwords differently, so read the manual.
- You are troubleshooting a no-POST problem and want a known-default starting point.
Before you start
Turn the PC off, switch off the power supply and unplug the power cable. Guides from board makers and PC builders suggest pressing the power button for a few seconds with the cable removed to drain residual power. Do not move jumpers or remove the battery while the board has standby power. Touch the metal case to discharge static before you handle components, and never open the power supply. Clearing CMOS wipes custom settings, so note any you want to restore, such as memory profile and fan curves, and keep overclocking conservative afterward, since changes can cause instability and may affect warranty terms.
Three methods compared
| Method | How it works | Best when | Watch out for |
|---|---|---|---|
| Clear CMOS button | Press the button, often on the rear I/O panel or the board, for the time the manual states | The board has one and you want the quickest route | Do it with the PC unplugged unless the manual says otherwise |
| Jumper | Move the jumper cap or bridge the pins for several seconds, then restore it | No button, and you can see the header | Leaving the jumper in the clear position can stop the board from starting |
| Remove the battery | Pop out the coin cell, wait, then replace it | No button or jumper is available | Some boards hold settings longer, so wait and combine with another method |
Method 1: Clear CMOS button
- Power down, switch off the PSU and unplug the cable.
- Find the button. On many boards it sits on the rear I/O panel or near the edge of the board. Names vary, such as Clear CMOS or CLR_CMOS.
- Press it for about five to ten seconds, as guides from makers such as ASUS describe, or follow your manual’s time.
- Reconnect power and start the PC. The board may display a message about settings having been reset.
Method 2: Jumper
- Power off and unplug. Find the clear header near the battery or at the bottom edge. Names differ by maker, for example CLRTC, JBAT1, CLR_CMOS or CLRCMOS1.
- On a three-pin header, move the cap from pins 1 and 2 to pins 2 and 3 for the time the manual states, often around a minute, then return it to the original position.
- On a two-pin header, briefly bridge the pins with a jumper cap as the manual describes. Remove it afterward.
- Do not leave the jumper in the clear position. A manual such as ASUS’s warns that this causes boot failure.
Method 3: Remove the battery
- Power off, unplug and drain power by holding the power button briefly.
- Find the coin cell. Press the retaining clip with a small plastic tool or a flat screwdriver, and lift the battery out.
- Leave it out for a few seconds up to several minutes. Reports differ, and a longer wait is safer on stubborn boards.
- Reinstall it with the positive side facing up, as marked, reconnect power and start the PC.
After the reset
Enter the BIOS on first boot. Check the date and time, boot drive order and storage mode, and re-enable memory profiles such as XMP or EXPO if you use them. Names differ across makers, so follow the manual. If the board reports a boot problem, load optimized defaults and save. If your fan curves are gone, set them again. A system that cannot reach Windows after the reset may have a changed storage or boot mode, so compare with how you set it before.
Common mistakes
- Clearing with the PSU still on and the board powered.
- Forgetting to return a jumper to the normal position.
- Pulling the battery for a second and giving up. Some boards need a longer wait or the jumper as well.
- Bending or dropping the coin cell clip, or inserting the battery upside down.
- Expecting a CMOS clear to fix a corrupted BIOS image. It resets settings, not firmware, so a failed flash needs a recovery feature.
Clear CMOS vs related terms
| Term | What it does |
|---|---|
| Clear CMOS | Erases saved BIOS settings, restoring defaults |
| Load optimized defaults | Resets settings from inside the BIOS menu when you can still reach it |
| BIOS flashback or recovery | Rewrites the firmware itself |
| Replace CMOS battery | Fixes a dead coin cell that loses time and settings |
Frequently Asked Questions
Will clearing CMOS delete my files or Windows?
No. It only resets BIOS settings. Your files and operating system stay on your drive, though a changed boot or storage setting may need to be restored.
How long should I leave the battery out?
Guides range from about five to ten seconds up to several minutes. If settings persist, wait longer or use the jumper or button method as well.
Can I clear CMOS without opening the case?
Some boards have a Clear CMOS button on the rear I/O panel, which means you do not need to open the case. Without it, you need access to the jumper or the battery.
Why does my PC beep or restart after clearing CMOS?
The board may retrain memory or notice that settings are default, so a restart or a longer first boot is common. If it does not complete, reseat the memory and consult the board manual.
How often should I change the CMOS battery?
A coin cell lasts years in typical use. If the clock resets or settings vanish after power-off, replace it with the same type the manual lists.
FAQ
Will clearing CMOS delete my files or Windows?
How long should I leave the battery out?
Can I clear CMOS without opening the case?
Why does my PC beep or restart after clearing CMOS?
How often should I change the CMOS battery?
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAs an Amazon Associate we earn from qualifying purchases.