Key takeaways
- Reallocated Sectors Count: a count above zero that keeps rising is a warning sign.
- Current Pending Sector Count: unstable sectors waiting to be remapped; any non-zero value deserves attention.
- Uncorrectable Sector Count: read or write errors that could not be fixed.
- Temperature: sustained high readings shorten life; check the drive maker’s rating.
The fastest way to check drive health on a Windows gaming PC is to read the drive’s SMART data with a free tool such as CrystalDiskInfo, or to open Windows Settings, go to System, Storage, then Advanced storage settings and Disks and volumes, and look at the drive’s properties for its health estimate. Either route tells you in under a minute whether the drive reports a problem.
What “Drive Health” Actually Means
SMART (Self-Monitoring, Analysis and Reporting Technology) is a set of counters that hard drives and SSDs keep about themselves. For mechanical drives, the key counters include reallocated sectors, current pending sectors, and uncorrectable errors. A widely cited Google study, as summarized on the SMART reference page, found that drives with early reallocation errors were far more likely to fail, but it also found that a large share of failed drives showed no SMART warnings other than temperature. In other words, SMART can warn you, but a clean report is not a guarantee.
NVMe SSDs report a different, standardized set of fields. Two matter most: Percentage Used, an estimate of how much of the drive’s rated life has been consumed (usually based on writes), and Critical Warning, which flags conditions such as low spare capacity, over-temperature, degraded reliability, read-only mode, or a backup power failure.
Quick Reference: Tools and What They Show
| Tool | Works for | What you see | Skill level |
|---|---|---|---|
| Windows Settings, Disks and volumes | Many SSDs in current Windows 11 builds | Drive health estimate, remaining life where supported | Beginner |
| CrystalDiskInfo | HDD, SATA SSD, NVMe | Health status, temperature, SMART attributes, hours powered on | Beginner |
| Maker utilities (Samsung Magician, WD Dashboard, Crucial Storage Executive and similar) | That brand’s drives | Health, firmware, sometimes TBW used | Beginner |
| Windows PowerShell Get-PhysicalDisk | Most drives | HealthStatus and OperationalStatus | Intermediate |
| chkdsk | File system on any drive | File system and bad sector scan | Intermediate |
| smartctl (smartmontools) | Most drives | Full SMART and NVMe log | Advanced |
Method 1: Windows Built-In Check
- Open Settings, then System, then Storage.
- Choose Advanced storage settings, then Disks and volumes.
- Select the drive and open Properties.
- Read the drive health or estimated remaining life if shown.
This view is simple and offered on newer builds, and the labels may differ by Windows version and by whether the drive reports the data. If you do not see it, use another method below.
Method 2: PowerShell for a Plain Status
Open PowerShell as an administrator and run Get-PhysicalDisk. The HealthStatus column should read Healthy. A Warning or Unhealthy value means Windows has detected a problem and you should back up at once. The older wmic diskdrive get status command reports a basic OK or Pred Fail, but wmic is being phased out of Windows, so PowerShell is the better path.
Method 3: CrystalDiskInfo and Brand Tools
CrystalDiskInfo displays a colored status for each drive: Good, Caution, Bad, or Unknown. It also lists temperature, power-on hours, and the raw SMART values. Download it from the maker’s own site only, and install the standard edition. Open the program and check each drive tab.
What to look at on a hard drive
- Reallocated Sectors Count: a count above zero that keeps rising is a warning sign.
- Current Pending Sector Count: unstable sectors waiting to be remapped; any non-zero value deserves attention.
- Uncorrectable Sector Count: read or write errors that could not be fixed.
- Temperature: sustained high readings shorten life; check the drive maker’s rating.
What to look at on an SSD
- Percentage Used (NVMe) or the maker’s life remaining value: shows wear against the rated endurance.
- Available Spare: reserve capacity; when it falls below its threshold the drive raises a warning.
- Media and data integrity errors: should stay at zero.
- Data written: compare to the TBW rating in the maker’s spec sheet.
Method 4: Scan the File System with chkdsk
SMART reports hardware counters, while chkdsk checks logical file system errors. In an administrator Command Prompt, running chkdsk with the drive letter checks the volume; adding the /f switch fixes file system errors and may require a restart for the system drive. Adding /r also looks for bad sectors on a hard drive and can take a long time. On SSDs, avoid repeated surface scans without cause, since the drive manages its own flash. If chkdsk finds repeated errors, treat the drive as suspect.
How to Read the Result
| Symptom or reading | Likely meaning | Action |
|---|---|---|
| Status Good or Healthy, counters at zero | No reported issues | Keep normal backups, re-check every few months |
| Caution or Warning | Counters crossed a threshold | Back up immediately, plan replacement |
| Rising reallocated or pending sectors on an HDD | Surface wear | Back up and replace; do not store sole copies |
| High Percentage Used on an SSD | Approaching rated write life | Back up and plan for a new drive |
| Drive disappears or freezes the PC | Connection, firmware, or hardware fault | Reseat cables, update firmware, contact the maker |
| Clicking or grinding from an HDD | Mechanical failure | Power off, stop using, seek a data recovery service |
| Status Unknown | Tool cannot read the data (often USB enclosures) | Try a maker tool or direct connection |
Safety and Common Mistakes
- Back up before running repair tools that write to the drive.
- Do not treat a Good status as proof of safety; SMART misses many failures.
- Switch off and unplug the PC before touching cables or reseating a drive, and never open a power supply.
- Avoid running full format or surface tests on a drive that already shows warnings.
- Do not rely on one tool; compare the Windows reading with a second source when something looks wrong.
- USB enclosures often hide SMART data, so a missing report is not a failure.
Keeping a Drive Healthy Longer
Good habits reduce risk but do not remove it. Keep the PC dust-filtered so airflow stays steady, since sustained heat is a stress factor for any drive. Use the maker’s utility to update SSD firmware, and leave some free space on the drive so it has room to manage writes; makers commonly suggest not running a drive completely full. Avoid moving or bumping a PC while a hard drive is spinning. Use a surge protector, because sudden power loss can corrupt data and stress drives. Most important, keep a second copy of anything you cannot replace, because health tools estimate risk and cannot stop a failure.
When to Contact the Maker or a Technician
If a drive is under warranty and reports Caution or Bad, read the maker’s support page for the warranty process, which often asks for the model and serial number and a screenshot of the health report. If the drive makes unusual noises or vanishes from the system, stop using it and consider a data recovery professional rather than running repeated repair tools. Never open a hard drive casing, and never open a power supply, because both can cause injury or permanent data loss.
Frequently Asked Questions
How often should I check drive health?
Every few months is reasonable for a gaming PC, and again if you see crashes, long freezes, or corrupted files. Keep regular backups regardless, since a failure can come with little warning.
Does a Good status mean my drive is safe?
No. Research summarized on the SMART reference page found many failed drives had no SMART errors beforehand. Treat the status as one signal alongside backups.
How do I know when an SSD is wearing out?
Watch Percentage Used on NVMe drives or the maker’s life remaining value, and compare data written with the TBW rating in the spec sheet. A rising count of media errors or low available spare is also a warning.
Can I check drive health without installing software?
Yes. Windows Settings can show a drive health estimate on supported builds, and PowerShell’s Get-PhysicalDisk reports HealthStatus. Both are built in.
What should I do if the drive shows Caution?
Copy your important data to another drive straight away, then check the maker’s warranty terms. Replacing the drive is the safe course while the data is still readable.
FAQ
How often should I check drive health?
Does a Good status mean my drive is safe?
How do I know when an SSD is wearing out?
Can I check drive health without installing software?
What should I do if the drive shows Caution?
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAs an Amazon Associate we earn from qualifying purchases.